国产MCU-CW32F030开发学习-ST7735 LCD模块
发布时间：2023-06-29 21:00:31
国产MCU-CW32F030开发学习-ST7735 LCD模块
硬件平台
CW32_48F大学计划板
CW32_IOT_EVA物联网开发评估套件
0.96 IIC oled模块ST7735 LCD模块 硬件接口使用的 2.54mm 间距的排针接口，这使用杜邦线进行连接.| ST7735 | 参数 || -------- | --------------- || 供电电压 | 3.3~5.5V || 驱动IC | ST7735 || 分辨率 | 128x128/128x160 || 尺寸 | 1.44 / 1.8寸 || 驱动接口 | 4线SPI |引脚功能 | 引脚名称 | 引脚功能 || -------- | -------------------------------------- || VCC | 电源正，3.3 - 5V，需要与通信电平一致 || GND | 电源负，地 || CS | 片选，低电平使能 || RST | 复位，低电平使能 || DC | 数据/命令选择，低电平命令，高电平数据 || SDA | SPI数据输入端口 || SCL | SPI时钟信号输入端口 || BLK | 背光，悬空使能接地关闭，默认上拉至3.3V |
文件结构如下：
Application:
main.c
main.h
interrupts_cw32f030.c
interrupts_cw32f030.h
startup_cw32f030.s
core_cm0plus.h
BspDriver:
bsp_led.c
bsp_led.h
bsp_lcd.c
bsp_lcd.h
FwlibLbibraries:
cw32f030_gpio.c
cw32f030_gpio.h
//cw32f030官方库函数文件
SystemLibraries:
//芯片系统资料配置文件
rcc_config.c
rcc_config.h
//uart timer rcc.....
Output:
编译过程输出文件 例如hex
main.c
#include "main.h"
/* 系统时钟配置为64M */
void Board_Iint(void)
{
RCC_Configuration(); //系统时钟64M
Lcd_Init();
LED_init();
}
int main()
{
unsigned char aht10_temp=20;
unsigned char aht10_humi=70;
Board_Iint();
Lcd_Clear(GRAY0); //清屏
Gui_DrawFont_GBK16(15,5,BLACK,GRAY0,"HELLO-CW32");
Gui_DrawFont_GBK16(15,25,RED,GRAY0,"CW32-48F-Board");
Gui_DrawFont_GBK16(15,45,RED,GRAY0,"By 2023-06-01");
Gui_DrawFont_GBK16(15,65,RED,GRAY0,"By CoderEnd");
TFT_ShowString_16x16(15,100,"Temp:",Blue1,White);
TFT_ShowString_16x16(15,120,"Humi:",Blue1,White);
TFT_ShowNumber_Float_16x16(60,100,aht10_temp,2,1,Red,White);
TFT_ShowNumber_Float_16x16(60,120,aht10_humi,2,1,Red,White);
while(1)
{
GPIO_TogglePin(LED1_GPIO_PORT, LED1_GPIO_PIN);
delay1ms(500);//延迟500ms
}
}
main.h
/* USER CODE BEGIN Header */
/** ****************************************************************************** * @file : main.h * @brief : Header for main.c file. * This file contains the common defines of the application. ****************************************************************************** * @attention * *
© Copyright (c) 2021 CW. * All rights reserved.
* * ****************************************************************************** */
/* USER CODE END Header */
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __MAIN_H
#define __MAIN_H
#ifdef __cplusplus
extern "C" {
#endif
//--------------------------------------------------------------------------------------------------
// Standard library | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//--------------------------------------------------------------------------------------------------
#include "base_types.h"
#include "cw32f030.h"
#include "system_cw32f030.h"
#include "interrupts_cw32f030.h"
#include "cw32f030_adc.h"
#include "cw32f030_atim.h"
#include "cw32f030_awt.h"
#include "cw32f030_btim.h"
#include "cw32f030_crc.h"
#include "cw32f030_debug.h"
#include "cw32f030_digitalsign.h"
#include "cw32f030_dma.h"
#include "cw32f030_flash.h"
#include "cw32f030_gpio.h"
#include "cw32f030_gtim.h"
#include "cw32f030_i2c.h"
#include "cw32f030_iwdt.h"
#include "cw32f030_lvd.h"
#include "cw32f030_pwr.h"
#include "cw32f030_ram.h"
#include "cw32f030_rcc.h"
#include "cw32f030_rtc.h"
#include "cw32f030_spi.h"
#include "cw32f030_systick.h"
#include "cw32f030_uart.h"
#include "cw32f030_wwdt.h"
//--------------------------------------------------------------------------------------------------
// 数据类型重定义 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//--------------------------------------------------------------------------------------------------
#include
#include
#include
#include "stdarg.h"
#include "stdlib.h" //函数调用头文件
#include "stdio.h" //为了解除sprintf警告
/************************************************************************************************** typedef unsigned char uint8_t; typedef unsigned short uint16_t; typedef unsigned long uint32_t; typedef unsigned long long int uint64_t; typedef signed char int8_t; typedef signed short int16_t; typedef signed long int32_t; typedef long long int int64_t; C语言数据类型 整型（int）、单精度浮点型（float） 双精度浮点型（double）、字符型（char） 整型（int）类型又划分了 long int（也可以直接写为long） 、long long int（可以直接写为long long） 、short int（可以直接写为short） 指针类型：void *； 空类型：void； 构造类型：数组、结构体（strtuct）、共用体类型（union）、枚举类型（enum）； 1字节(Byte) = 8位(bit) 1Byte=8bi ******************************************************************************************************/
//--------------------------------------------------------------------------------------------------
// 系统函数头文件 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//--------------------------------------------------------------------------------------------------
///* void delay1ms(uint32_t u32Cnt) //1ms延迟函数 // * \brief delay1ms // * delay approximately 1ms. // * \param [in] u32Cnt // * \retval void // */
#include "rcc_config.h"
//--------------------------------------------------------------------------------------------------
// 模块函数头文件 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//--------------------------------------------------------------------------------------------------
#include "bsp_lcd.h"
#include "bsp_led.h"
/* USER CODE END Includes */
/* Exported types ------------------------------------------------------------*/
/* USER CODE BEGIN ET */
/* USER CODE END ET */
/* Exported constants --------------------------------------------------------*/
/* USER CODE BEGIN EC */
/* USER CODE END EC */
/* Exported macro ------------------------------------------------------------*/
/* USER CODE BEGIN EM */
/* USER CODE END EM */
//--------------------------------------------------------------------------------------------------
// 引用函数声明 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//--------------------------------------------------------------------------------------------------
/* Exported functions prototypes ---------------------------------------------*/
/* USER CODE BEGIN EFP */
void Board_Iint(void); //硬件设备初始化
/* USER CODE END EFP */
/* Private defines -----------------------------------------------------------*/
/* USER CODE BEGIN Private defines */
/* USER CODE END Private defines */
#ifdef __cplusplus
}
#endif
#endif /* __MAIN_H */
/************************ (C) COPYRIGHT CW *****END OF FILE****/
bsp_lcd.c
//---------------- ----------------------------------------------------------------------------------
// 包含的头文件 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//--------------------------------------------------------------------------------------------------
#include "main.h"
#include "font.h"
//==================================================================================================
// 实现功能: LCD_GPIO_Init
// 函数说明: //液晶IO初始化配置
// 函数备注:
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void LCD_GPIO_Init(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
__RCC_GPIOB_CLK_ENABLE();
__RCC_GPIOA_CLK_ENABLE();
GPIO_InitStruct.IT = GPIO_IT_NONE; //LED1
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pins = GPIO_PIN_0;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Pins = GPIO_PIN_4| GPIO_PIN_5| GPIO_PIN_6| GPIO_PIN_7;
GPIO_Init(CW_GPIOB, &GPIO_InitStruct);
GPIO_InitStruct.Pins = GPIO_PIN_15;
GPIO_Init(CW_GPIOA, &GPIO_InitStruct);
}
//==================================================================================================
// 实现功能: SPI_WriteData
// 函数说明: 向SPI总线传输一个8位数据
// 函数备注:
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void SPI_WriteData(unsigned char Data)
{
unsigned char i=0;
for(i=8;i>0;i--)
{
if(Data&0x80)
LCD_SDA_SET; //输出数据
else LCD_SDA_CLR;
LCD_SCL_CLR;
LCD_SCL_SET;
Data<<=1;
}
}
//==================================================================================================
// 实现功能: Lcd_WriteIndex
// 函数说明: 向液晶屏写一个8位指令
// 函数备注:
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Lcd_WriteIndex(unsigned char Index)
{
//SPI 写命令时序开始
LCD_CS_CLR;
LCD_RS_CLR;
SPI_WriteData(Index);
LCD_CS_SET;
}
//==================================================================================================
// 实现功能: Lcd_WriteData
// 函数说明: 向液晶屏写一个8位数据
// 函数备注:
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Lcd_WriteData(unsigned char Data)
{
LCD_CS_CLR;
LCD_RS_SET;
SPI_WriteData(Data);
LCD_CS_SET;
}
//==================================================================================================
// 实现功能: LCD_WriteData_16Bit
// 函数说明: 向液晶屏写一个16位数据
// 函数备注:
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
//向液晶屏写一个16位数据
void LCD_WriteData_16Bit(unsigned short Data)
{
LCD_CS_CLR;
LCD_RS_SET;
SPI_WriteData(Data>>8); //写入高8位数据
SPI_WriteData(Data); //写入低8位数据
LCD_CS_SET;
}
//==================================================================================================
// 实现功能: Lcd_WriteReg
// 函数说明: 写寄存器内容函数
// 函数备注:
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Lcd_WriteReg(unsigned char Index,unsigned char Data)
{
Lcd_WriteIndex(Index);
Lcd_WriteData(Data);
}
//==================================================================================================
// 实现功能: Lcd_Reset
// 函数说明: LCD复位
// 函数备注:
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Lcd_Reset(void)
{
unsigned int i;
LCD_RST_CLR;
//delay_ms(100);
for(i=0;i<6000;i++);
LCD_RST_SET;
for(i=0;i<6000;i++);
}
//==================================================================================================
// 实现功能: Lcd_Init
// 函数说明: LCD硬件初始化
// 函数备注: LCD Init For 1.70Inch LCD Panel with ST7735R.
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Lcd_Init(void)
{
unsigned int i;
LCD_GPIO_Init();
Lcd_Reset(); //Reset before LCD Init.
//LCD Init For 1.44Inch LCD Panel with ST7735R.
Lcd_WriteIndex(0x11);//Sleep exit
//delay_ms (120);
for(i=0;i<65000;i++);
for(i=0;i<65000;i++);
//ST7735R Frame Rate
Lcd_WriteIndex(0xB1);
Lcd_WriteData(0x01);
Lcd_WriteData(0x2C);
Lcd_WriteData(0x2D);
Lcd_WriteIndex(0xB2);
Lcd_WriteData(0x01);
Lcd_WriteData(0x2C);
Lcd_WriteData(0x2D);
Lcd_WriteIndex(0xB3);
Lcd_WriteData(0x01);
Lcd_WriteData(0x2C);
Lcd_WriteData(0x2D);
Lcd_WriteData(0x01);
Lcd_WriteData(0x2C);
Lcd_WriteData(0x2D);
Lcd_WriteIndex(0xB4); //Column inversion
Lcd_WriteData(0x07);
//ST7735R Power Sequence
Lcd_WriteIndex(0xC0);
Lcd_WriteData(0xA2);
Lcd_WriteData(0x02);
Lcd_WriteData(0x84);
Lcd_WriteIndex(0xC1);
Lcd_WriteData(0xC5);
Lcd_WriteIndex(0xC2);
Lcd_WriteData(0x0A);
Lcd_WriteData(0x00);
Lcd_WriteIndex(0xC3);
Lcd_WriteData(0x8A);
Lcd_WriteData(0x2A);
Lcd_WriteIndex(0xC4);
Lcd_WriteData(0x8A);
Lcd_WriteData(0xEE);
Lcd_WriteIndex(0xC5); //VCOM
Lcd_WriteData(0x0E);
Lcd_WriteIndex(0x36); //MX, MY, RGB mode
Lcd_WriteData(0xC0);
//ST7735R Gamma Sequence
Lcd_WriteIndex(0xe0);
Lcd_WriteData(0x0f);
Lcd_WriteData(0x1a);
Lcd_WriteData(0x0f);
Lcd_WriteData(0x18);
Lcd_WriteData(0x2f);
Lcd_WriteData(0x28);
Lcd_WriteData(0x20);
Lcd_WriteData(0x22);
Lcd_WriteData(0x1f);
Lcd_WriteData(0x1b);
Lcd_WriteData(0x23);
Lcd_WriteData(0x37);
Lcd_WriteData(0x00);
Lcd_WriteData(0x07);
Lcd_WriteData(0x02);
Lcd_WriteData(0x10);
Lcd_WriteIndex(0xe1);
Lcd_WriteData(0x0f);
Lcd_WriteData(0x1b);
Lcd_WriteData(0x0f);
Lcd_WriteData(0x17);
Lcd_WriteData(0x33);
Lcd_WriteData(0x2c);
Lcd_WriteData(0x29);
Lcd_WriteData(0x2e);
Lcd_WriteData(0x30);
Lcd_WriteData(0x30);
Lcd_WriteData(0x39);
Lcd_WriteData(0x3f);
Lcd_WriteData(0x00);
Lcd_WriteData(0x07);
Lcd_WriteData(0x03);
Lcd_WriteData(0x10);
Lcd_WriteIndex(0x2a);
Lcd_WriteData(0x00);
Lcd_WriteData(0x00);
Lcd_WriteData(0x00);
Lcd_WriteData(0x7f);
Lcd_WriteIndex(0x2b);
Lcd_WriteData(0x00);
Lcd_WriteData(0x00);
Lcd_WriteData(0x00);
Lcd_WriteData(0x9f);
Lcd_WriteIndex(0xF0); //Enable test command
Lcd_WriteData(0x01);
Lcd_WriteIndex(0xF6); //Disable ram power save mode
Lcd_WriteData(0x00);
Lcd_WriteIndex(0x3A); //65k mode
Lcd_WriteData(0x05);
Lcd_WriteIndex(0x29);//Display on
}
/************************************************* 函数名：LCD_Set_Region 功能：设置lcd显示区域，在此区域写点数据自动换行 入口参数：xy起点和终点 返回值：无 *************************************************/
void Lcd_SetRegion(unsigned short x_start,unsigned short y_start,unsigned short x_end,unsigned short y_end)
{
Lcd_WriteIndex(0x2a);
Lcd_WriteData(0x00);
Lcd_WriteData(x_start);//Lcd_WriteData(x_start+2);
Lcd_WriteData(0x00);
Lcd_WriteData(x_end+2);
Lcd_WriteIndex(0x2b);
Lcd_WriteData(0x00);
Lcd_WriteData(y_start+0);
Lcd_WriteData(0x00);
Lcd_WriteData(y_end+1);
Lcd_WriteIndex(0x2c);
}
/************************************************* 函数名：LCD_Set_XY 功能：设置lcd显示起始点 入口参数：xy坐标 返回值：无 *************************************************/
void Lcd_SetXY(unsigned short x,unsigned short y)
{
Lcd_SetRegion(x,y,x,y);
}
/************************************************* 函数名：LCD_DrawPoint 功能：画一个点 入口参数：无 返回值：无 *************************************************/
void Gui_DrawPoint(unsigned short x,unsigned short y,unsigned short Data)
{
Lcd_SetRegion(x,y,x+1,y+1);
LCD_WriteData_16Bit(Data);
}
/***************************************** 函数功能：读TFT某一点的颜色 出口参数：color 点颜色值 ******************************************/
unsigned int Lcd_ReadPoint(unsigned short x,unsigned short y)
{
unsigned int Data;
Lcd_SetXY(x,y);
Lcd_WriteData(Data);
return Data;
}
/************************************************* 函数名：Lcd_Clear 功能：全屏清屏函数 入口参数：填充颜色COLOR 返回值：无 *************************************************/
void Lcd_Clear(unsigned short Color)
{
unsigned int i,m;
Lcd_SetRegion(0,0,X_MAX_PIXEL-1,Y_MAX_PIXEL-1);
Lcd_WriteIndex(0x2C);
for(i=0;i>0)&0x1f;
g=(c>>5)&0x3f;
r=(c>>11)&0x1f;
rgb=(b<<11)+(g<<5)+(r<<0);
return(rgb);
}
//==================================================================================================
// 实现功能: Gui_Circle
// 函数说明: 画圆函数
// 函数备注: Bresenham算法
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Gui_Circle(unsigned short X,unsigned short Y,unsigned short R,unsigned short fc)
{
unsigned short a,b;
int c;
a=0;
b=R;
c=3-2*R;
while (a=0)
{
x_inc = 1;
}
else
{
x_inc = -1;
dx = -dx;
}
if (dy>=0)
{
y_inc = 1;
}
else
{
y_inc = -1;
dy = -dy;
}
dx2 = dx << 1;
dy2 = dy << 1;
if (dx > dy)//x距离大于y距离，那么每个x轴上只有一个点，每个y轴上有若干个点
{ //且线的点数等于x距离，以x轴递增画点
// initialize error term
error = dy2 - dx;
// draw the line
for (index=0; index <= dx; index++)//要画的点数不会超过x距离
{
//画点
Gui_DrawPoint(x0,y0,Color);
// test if error has overflowed
if (error >= 0) //是否需要增加y坐标值
{
error-=dx2;
// move to next line
y0+=y_inc;//增加y坐标值
} // end if error overflowed
// adjust the error term
error+=dy2;
// move to the next pixel
x0+=x_inc;//x坐标值每次画点后都递增1
} // end for
} // end if |slope| <= 1
else//y轴大于x轴，则每个y轴上只有一个点，x轴若干个点
{ //以y轴为递增画点
// initialize error term
error = dx2 - dy;
// draw the line
for (index=0; index <= dy; index++)
{
// set the pixel
Gui_DrawPoint(x0,y0,Color);
// test if error overflowed
if (error >= 0)
{
error-=dy2;
// move to next line
x0+=x_inc;
} // end if error overflowed
// adjust the error term
error+=dx2;
// move to the next pixel
y0+=y_inc;
} // end for
} // end else |slope| > 1
}
//==================================================================================================
// 实现功能: Gui_box
// 函数说明: 画矩形函数
// 函数备注:
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Gui_box(unsigned short x, unsigned short y, unsigned short w, unsigned short h,unsigned short bc)
{
Gui_DrawLine(x,y,x+w,y,0xEF7D);
Gui_DrawLine(x+w-1,y+1,x+w-1,y+1+h,0x2965);
Gui_DrawLine(x,y+h,x+w,y+h,0x2965);
Gui_DrawLine(x,y,x,y+h,0xEF7D);
Gui_DrawLine(x+1,y+1,x+1+w-2,y+1+h-2,bc);
}
void Gui_box2(unsigned short x,unsigned short y,unsigned short w,unsigned short h, unsigned char mode)
{
if (mode==0)
{
Gui_DrawLine(x,y,x+w,y,0xEF7D);
Gui_DrawLine(x+w-1,y+1,x+w-1,y+1+h,0x2965);
Gui_DrawLine(x,y+h,x+w,y+h,0x2965);
Gui_DrawLine(x,y,x,y+h,0xEF7D);
}
if (mode==1)
{
Gui_DrawLine(x,y,x+w,y,0x2965);
Gui_DrawLine(x+w-1,y+1,x+w-1,y+1+h,0xEF7D);
Gui_DrawLine(x,y+h,x+w,y+h,0xEF7D);
Gui_DrawLine(x,y,x,y+h,0x2965);
}
if (mode==2)
{
Gui_DrawLine(x,y,x+w,y,0xffff);
Gui_DrawLine(x+w-1,y+1,x+w-1,y+1+h,0xffff);
Gui_DrawLine(x,y+h,x+w,y+h,0xffff);
Gui_DrawLine(x,y,x,y+h,0xffff);
}
}
/************************************************************************************** 功能描述: 在屏幕显示一凸起的按钮框 输 入: unsigned short x1,y1,x2,y2 按钮框左上角和右下角坐标 输 出: 无 **************************************************************************************/
void DisplayButtonDown(unsigned short x1,unsigned short y1,unsigned short x2,unsigned short y2)
{
Gui_DrawLine(x1, y1, x2,y1, GRAY2); //H
Gui_DrawLine(x1+1,y1+1,x2,y1+1, GRAY1); //H
Gui_DrawLine(x1, y1, x1,y2, GRAY2); //V
Gui_DrawLine(x1+1,y1+1,x1+1,y2, GRAY1); //V
Gui_DrawLine(x1, y2, x2,y2, WHITE); //H
Gui_DrawLine(x2, y1, x2,y2, WHITE); //V
}
/************************************************************************************** 功能描述: 在屏幕显示一凹下的按钮框 输 入: unsigned short x1,y1,x2,y2 按钮框左上角和右下角坐标 输 出: 无 **************************************************************************************/
void DisplayButtonUp(unsigned short x1,unsigned short y1,unsigned short x2,unsigned short y2)
{
Gui_DrawLine(x1, y1, x2,y1, WHITE); //H
Gui_DrawLine(x1, y1, x1,y2, WHITE); //V
Gui_DrawLine(x1+1,y2-1,x2,y2-1, GRAY1); //H
Gui_DrawLine(x1, y2, x2,y2, GRAY2); //H
Gui_DrawLine(x2-1,y1+1,x2-1,y2, GRAY1); //V
Gui_DrawLine(x2 ,y1 ,x2,y2, GRAY2); //V
}
//==================================================================================================
// 实现功能: Gui_DrawFont_GBK16
// 函数说明:
// 函数备注: fc:font Color bc :background Color
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Gui_DrawFont_GBK16(unsigned short x, unsigned short y, unsigned short fc, unsigned short bc, unsigned char *s)
{
unsigned char i,j;
unsigned short k,x0;
x0=x;
while(*s)
{
if((*s) < 128)
{
k=*s;
if (k==13)
{
x=x0;
y+=16;
}
else
{
if (k>32) k-=32; else k=0;
for(i=0;i<16;i++)
for(j=0;j<8;j++)
{
if(asc16[k*16+i]&(0x80>>j)) Gui_DrawPoint(x+j,y+i,fc);
else
{
if (fc!=bc) Gui_DrawPoint(x+j,y+i,bc);
}
}
x+=8;
}
s++;
}
else
{
for (k=0;k>j)) Gui_DrawPoint(x+j,y+i,fc);
else {
if (fc!=bc) Gui_DrawPoint(x+j,y+i,bc);
}
}
for(j=0;j<8;j++)
{
if(hz16[k].Msk[i*2+1]&(0x80>>j)) Gui_DrawPoint(x+j+8,y+i,fc);
else
{
if (fc!=bc) Gui_DrawPoint(x+j+8,y+i,bc);
}
}
}
}
}
s+=2;x+=16;
}
}
}
//==================================================================================================
// 实现功能: Gui_DrawFont_GBK24
// 函数说明:
// 函数备注: fc:font Color bc :background Color
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Gui_DrawFont_GBK24(unsigned short x, unsigned short y, unsigned short fc, unsigned short bc, unsigned char *s)
{
unsigned char i,j;
unsigned short k;
while(*s)
{
if( *s < 0x80 )
{
k=*s;
if (k>32) k-=32; else k=0;
for(i=0;i<16;i++)
for(j=0;j<8;j++)
{
if(asc16[k*16+i]&(0x80>>j))
Gui_DrawPoint(x+j,y+i,fc);
else
{
if (fc!=bc) Gui_DrawPoint(x+j,y+i,bc);
}
}
s++;x+=8;
}
else
{
for (k=0;k>j))
Gui_DrawPoint(x+j,y+i,fc);
else
{
if (fc!=bc) Gui_DrawPoint(x+j,y+i,bc);
}
}
for(j=0;j<8;j++)
{
if(hz24[k].Msk[i*3+1]&(0x80>>j)) Gui_DrawPoint(x+j+8,y+i,fc);
else {
if (fc!=bc) Gui_DrawPoint(x+j+8,y+i,bc);
}
}
for(j=0;j<8;j++)
{
if(hz24[k].Msk[i*3+2]&(0x80>>j))
Gui_DrawPoint(x+j+16,y+i,fc);
else
{
if (fc!=bc) Gui_DrawPoint(x+j+16,y+i,bc);
}
}
}
}
}
s+=2;x+=24;
}
}
}
//==================================================================================================
// 实现功能: Gui_DrawFont_Num32
// 函数说明:
// 函数备注: fc:font Color bc :background Color
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void Gui_DrawFont_Num32(unsigned short x, unsigned short y, unsigned short fc, unsigned short bc, unsigned short num)
{
unsigned char i,j,k,c;
for(i=0;i<32;i++)
{
for(j=0;j<4;j++)
{
c=*(sz32+num*32*4+i*4+j);
for (k=0;k<8;k++)
{
if(c&(0x80>>k))
Gui_DrawPoint(x+j*8+k,y+i,fc);
else
{
if (fc!=bc)
Gui_DrawPoint(x+j*8+k,y+i,bc);
}
}
}
}
}
//==================================================================================================
// 实现功能: TFT 定位光标
// 函数标记: 外设驱动函数
// 函数说明: 无
//--------------------------------------------------------------------------------------------------
// 输入参量: X_Start - X起始坐标 取值范围 - 0~239
// Y_Start - Y起始坐标 取值范围 - 0~239
// X_End - X终止坐标 取值范围 - 0~239
// Y_End - Y终止坐标 取值范围 - 0~239
// 输出参量: 无
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void TFT_SetArea(unsigned short X_Start,unsigned short Y_Start,unsigned short X_End,unsigned short Y_End)
{
// 执行相应操作
#if (TFT_FUNCTION_SCREEEN_VH == 0) // 竖屏
{
Lcd_WriteIndex(0x2A);
Lcd_WriteData(0x02);
Lcd_WriteData(X_Start+2);
Lcd_WriteData(0x02);
Lcd_WriteData(X_End+2);
Lcd_WriteIndex(0x2B);
Lcd_WriteData(0x01);
Lcd_WriteData(Y_Start+1);
Lcd_WriteData(0x01);
Lcd_WriteData(Y_End+1);
}
#endif // #if (TFT_FUNCTION_SCREEEN_VH == 0)
#if (TFT_FUNCTION_SCREEEN_VH == 1) // 横屏 待调整
{
Lcd_WriteIndex(0x2A);
Lcd_WriteData(0x02);
Lcd_WriteData(X_Start+1);
Lcd_WriteData(0x02);
Lcd_WriteData(X_End+1);
Lcd_WriteIndex(0x2B);
Lcd_WriteData(0x01);
Lcd_WriteData(Y_Start+2);
Lcd_WriteData(0x01);
Lcd_WriteData(Y_End+2);
}
#endif // #if (TFT_FUNCTION_SCREEEN_VH == 1)
Lcd_WriteIndex(0x2C);
}
//==================================================================================================
// 实现功能: TFT 指定位置 显示ASCII字符 08x16像素
// 函数标记: 外设驱动函数
// 函数说明: 1. 位置选取不恰当 可能造成字符串显示不完全
// 2. 如果字库不存在该文字则不显示
//--------------------------------------------------------------------------------------------------
// 输入参量: X - X方向坐标 取值范围 - 详情见宏定义TFT_SHOWSIZE_X
// Y - Y方向坐标 取值范围 - 详情见宏定义TFT_SHOWSIZE_Y
// ASCII - 待显示ASCII字符 取值范围 - ASCII字符
// FontColor - 字体颜色 取值范围 - 详情见枚举类型enumTFT_Color
// BackgroundColor - 背景颜色 取值范围 - 详情见枚举类型enumTFT_Color
// 输出参量: 无
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void TFT_ShowASCII_08x16(unsigned short X, unsigned short Y,unsigned char ASCII, enumTFT_Color FontColor, enumTFT_Color BackgroundColor)
{
unsigned char i,j,k; // 定义局部变量 用于循环计数
unsigned char Data; // 定义局部变量 用于临时存储
unsigned char FontCount; // 定义局部变量 用于记录字符字库个数
FontCount = sizeof(TFT_ASCII_08x16_FontCode)/sizeof(TFT_ASCII_08x16_FontCode[0]);
for(i=0; i 5)
{
Count = 5;
}
// 装载显示字符
Number_Integer_Array[0] = (IntegerNumber / 10000) % 10 + 0x30;
Number_Integer_Array[1] = (IntegerNumber / 1000 ) % 10 + 0x30;
Number_Integer_Array[2] = (IntegerNumber / 100 ) % 10 + 0x30;
Number_Integer_Array[3] = (IntegerNumber / 10 ) % 10 + 0x30;
Number_Integer_Array[4] = (IntegerNumber / 1 ) % 10 + 0x30;
Number_Integer_Array[5] = '\0';
// 执行显示操作
TFT_ShowString_16x16(X+8, Y, &Number_Integer_Array[5-Count], FontColor, BackgroundColor);
}
//==================================================================================================
// 实现功能: TFT 指定位置 显示无符号整形数字 16x16像素
// 函数标记: 外设驱动函数
// 函数说明: 1. 位置选取不恰当 可能造成数字显示不完全
// 2. 注意输入数字的取值范围
//--------------------------------------------------------------------------------------------------
// 输入参量: X - X方向坐标 取值范围 - 详情见宏定义TFT_SHOWSIZE_X
// Y - Y方向坐标 取值范围 - 详情见宏定义TFT_SHOWSIZE_Y
// IntegerNumber - 待显示整型数字 取值范围 - -32767~+32768
// Count - 待显示整型数字长度 取值范围 - 0~5
// FontColor - 字体颜色 取值范围 - 详情见枚举类型enumTFT_Color
// BackgroundColor - 背景颜色 取值范围 - 详情见枚举类型enumTFT_Color
// 输出参量: 无
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void TFT_ShowNumber_UnsignedInteger_16x16(unsigned short X, unsigned short Y, unsigned short IntegerNumber, unsigned char Count, enumTFT_Color FontColor, enumTFT_Color BackgroundColor)
{
unsigned char Number_Integer_Array[6] = { 0}; // 定义局部数据 用于装载显示数据
// 限制 显示字符数
if(Count > 5)
{
Count = 5;
}
// 装载显示字符
Number_Integer_Array[0] = (IntegerNumber / 10000) % 10 + 0x30;
Number_Integer_Array[1] = (IntegerNumber / 1000 ) % 10 + 0x30;
Number_Integer_Array[2] = (IntegerNumber / 100 ) % 10 + 0x30;
Number_Integer_Array[3] = (IntegerNumber / 10 ) % 10 + 0x30;
Number_Integer_Array[4] = (IntegerNumber / 1 ) % 10 + 0x30;
Number_Integer_Array[5] = '\0';
// 执行显示操作
TFT_ShowString_16x16(X, Y, &Number_Integer_Array[5-Count], FontColor, BackgroundColor);
}
//==================================================================================================
// 实现功能: TFT 指定位置 显示浮点数字 16x16像素
// 函数标记: 外设驱动函数
// 函数说明: 1. 位置选取不恰当 可能造成数字显示不完全
// 2. float型数据的有效数字7位 double型数据的有效数字16位
//--------------------------------------------------------------------------------------------------
// 输入参量: X - X方向坐标 取值范围 - 详情见宏定义TFT_SHOWSIZE_X
// Y - Y方向坐标 取值范围 - 详情见宏定义TFT_SHOWSIZE_Y
// FloatNumber - 待显示浮点型数字 取值范围 - -99999.99999~99999.99999
// Count1 - 整数显示位数 取值范围 - 0~5
// Count2 - 小数显示位数 取值范围 - 0~5
// FontColor - 字体颜色 取值范围 - 详情见枚举类型enumTFT_Color
// BackgroundColor - 背景颜色 取值范围 - 详情见枚举类型enumTFT_Color
// 输出参量: 无
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void TFT_ShowNumber_Float_16x16(unsigned short X, unsigned short Y, float FloatNumber, unsigned char Count1, unsigned char Count2, enumTFT_Color FontColor, enumTFT_Color BackgroundColor)
{
unsigned char Number_Integer_Array[6]; // 定义局部数组 用于存储整数位各位数据
unsigned char Number_Decimal_Array[6]; // 定义局部数组 用于存储小数位各位数据
unsigned long int Number_Integer = 0; // 定义局部变量 表示浮点数的 整数部分
unsigned long int Number_Decimal = 0; // 定义局部变量 表示浮点数的 小数部分
// 判断数字正负型
if(FloatNumber < 0)
{
FloatNumber = 0-FloatNumber;
TFT_ShowASCII_08x16(X, Y, '-', FontColor, BackgroundColor);
}
else
{
TFT_ShowASCII_08x16(X, Y, '+', FontColor, BackgroundColor);
}
// 限制 显示字符数
// 由于由于float型的有效十进制数值最多为7位，即整数位 + 小数位 数量一定小于等于7
while((Count1 + Count2 > 7 ))
{
if((Count1 > 5) && (Count1 != 0))
{
--Count1;
}
else
{
--Count2;
}
}
// 计算浮点数字的整数部分与小数部分
Number_Integer = (unsigned long int)(FloatNumber); // 取整数部分
Number_Decimal = (unsigned long int)((FloatNumber - Number_Integer + 0.000005) * 1e5); // 取小数部分，1e5科学计数法
// 装载显示字符
Number_Integer_Array[0] = Number_Integer/10000 % 10 + 0x30; // 计算整数部分
Number_Integer_Array[1] = Number_Integer/ 1000 % 10 + 0x30;
Number_Integer_Array[2] = Number_Integer/ 100 % 10 + 0x30;
Number_Integer_Array[3] = Number_Integer/ 10 % 10 + 0x30;
Number_Integer_Array[4] = Number_Integer/ 1 % 10 + 0x30;
Number_Integer_Array[5] = '\0';
Number_Decimal_Array[0] = Number_Decimal/10000 % 10 + 0x30; // 计算小数部分
Number_Decimal_Array[1] = Number_Decimal/ 1000 % 10 + 0x30;
Number_Decimal_Array[2] = Number_Decimal/ 100 % 10 + 0x30;
Number_Decimal_Array[3] = Number_Decimal/ 10 % 10 + 0x30;
Number_Decimal_Array[4] = Number_Decimal/ 1 % 10 + 0x30;
Number_Decimal_Array[Count2] = '\0';
// 执行显示操作
TFT_ShowString_16x16(X+8, Y, &Number_Integer_Array[5-Count1], FontColor, BackgroundColor);
TFT_ShowASCII_08x16( X+(1+Count1)*8, Y, '.', FontColor, BackgroundColor);
TFT_ShowString_16x16(X+(2+Count1)*8, Y, &Number_Decimal_Array[0], FontColor, BackgroundColor);
}
//==================================================================================================
// 实现功能: TFT 指定位置 显示二进制数字 16x16像素
// 函数标记: 外设驱动函数
// 函数说明: 1. 位置选取不恰当 可能造成字符串显示不完全
// 2. 注意输入数字的取值范围
//--------------------------------------------------------------------------------------------------
// 输入参量: X - X方向坐标 取值范围 - 详情见宏定义TFT_SHOWSIZE_X
// Y - Y方向坐标 取值范围 - 详情见宏定义TFT_SHOWSIZE_Y
// BinaryNumber - 待显示二进制数字 取值范围 - 0~65535
// Count - 二进制显示位数 取值范围 - 1~16
// FontColor - 字体颜色 取值范围 - 详情见枚举类型enumTFT_Color
// BackgroundColor - 背景颜色 取值范围 - 详情见枚举类型enumTFT_Color
// 输出参量: 无
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void TFT_ShowNumber_Binary_16x16(unsigned short X, unsigned short Y, unsigned short BinaryNumber, unsigned char Count, enumTFT_Color FontColor, enumTFT_Color BackgroundColor)
{
unsigned char i; // 定义局部变量，用于函数循环计数
for(i=Count; i>0; i--)
{
if(BinaryNumber & ( 1 << (Count-1) ))
{
TFT_ShowASCII_08x16(X, Y, '1', FontColor, BackgroundColor); // 显示二进制字符'1'
}
else
{
TFT_ShowASCII_08x16(X, Y, '0', FontColor, BackgroundColor); // 显示二进制字符'1'
}
BinaryNumber <<= 1; // 移位运算
X += 6; // 数组位置下一个位置
}
}
////取模方式 水平扫描 从左到右 低位在前
//void TFT_ShowImage(const unsigned char *p)
//{
// int i,j,k;
// unsigned char picH,picL;
// Lcd_Clear(WHITE); //清屏
//
// for(k=0;k<4;k++)
// {
// for(j=0;j<3;j++)
// {
// Lcd_SetRegion(40*j+2,40*k,40*j+39,40*k+39); //坐标设置
// for(i=0;i<40*40;i++)
// {
// picL=*(p+i*2); //数据低位在前
// picH=*(p+i*2+1);
// LCD_WriteData_16Bit(picH<<8|picL);
// }
// }
// }
//}
//==================================================================================================
// 实现功能: TFT 指定位置 显示图像
// 函数标记: 外设驱动函数
// 函数说明: 1. 位置选取不恰当 可能造成显示不完全
// 2. 注意输入数字的取值范围
//--------------------------------------------------------------------------------------------------
// 输入参量: X - X方向坐标
// Y - Y方向坐标
// Length 图片长度
// Width 图片宽度
// Pic[] 图片数组
// 输出参量: 无
//--------------------------------------------------------------------------------------------------
// | - | - | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//==================================================================================================
void TFT_ShowImage(unsigned short X,unsigned short Y,unsigned short Length,unsigned short Width,const unsigned char Pic[])
{
unsigned short i,j;
unsigned int k=0;
TFT_SetArea(X,Y,X+Length-1,Y+Width-1);
for(i=0;i>TFT --SCL/SCK
#define LCD_SDA GPIO_PIN_7 //PB7 MOSI--->>TFT --SDA/DIN
#define LCD_CS GPIO_PIN_5 //MCU_PB5--->>TFT --CS/CE
#define LCD_RS GPIO_PIN_4 //PB11--->>TFT --RS/DC
#define LCD_RST GPIO_PIN_15 //PB10--->>TFT --RST
//液晶控制口置1操作语句宏定义
#define LCD_SCL_SET LCD_CTRLB->BSRR=LCD_SCL
#define LCD_SDA_SET LCD_CTRLB->BSRR=LCD_SDA
#define LCD_CS_SET LCD_CTRLB->BSRR=LCD_CS
#define LCD_LED_SET LCD_CTRLA->BSRR=LCD_LED
#define LCD_RS_SET LCD_CTRLB->BSRR=LCD_RS
#define LCD_RST_SET LCD_CTRLA->BSRR=LCD_RST
//液晶控制口置0操作语句宏定义
#define LCD_SCL_CLR LCD_CTRLB->BRR=LCD_SCL
#define LCD_SDA_CLR LCD_CTRLB->BRR=LCD_SDA
#define LCD_CS_CLR LCD_CTRLB->BRR=LCD_CS
#define LCD_LED_CLR LCD_CTRLA->BRR=LCD_LED
#define LCD_RST_CLR LCD_CTRLA->BRR=LCD_RST
#define LCD_RS_CLR LCD_CTRLB->BRR=LCD_RS
#define LCD_DATAOUT(x) LCD_DATA->ODR=x; //数据输出
#define LCD_DATAIN LCD_DATA->IDR; //数据输入
#define LCD_WR_DATA(data){\ LCD_RS_SET;\ LCD_CS_CLR;\ LCD_DATAOUT(data);\ LCD_WR_CLR;\ LCD_WR_SET;\ LCD_CS_SET;\ }
//--------------------------------------------------------------------------------------------------
// 定义引用变量 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//--------------------------------------------------------------------------------------------------
// TFT 显示颜色 枚举
typedef enum enumTFT_Color
{
White = 0xFFFF, // 白色
Black = 0x0000, // 黑色
Blue1 = 0x001F, // 浅蓝色
Blue2 = 0x051F, // 深蓝色
Red = 0xF800, // 红色
Magenta = 0xF81F, // 品红色
Green = 0x07E0, // 绿色
Cyan = 0x7FFF, // 青色
Yellow = 0xFFE0, // 黄色
}enumTFT_Color;
//--------------------------------------------------------------------------------------------------
// 引用函数声明 | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
//--------------------------------------------------------------------------------------------------
void LCD_GPIO_Init(void);
void Lcd_WriteIndex(unsigned char Index);
void Lcd_WriteData(unsigned char Data);
void Lcd_WriteReg(unsigned char Index,unsigned char Data);
unsigned short Lcd_ReadReg(unsigned char LCD_Reg);
void Lcd_Reset(void);
void Lcd_Init(void);
void Lcd_Clear(unsigned short Color);
void Lcd_SetXY(unsigned short x,unsigned short y);
void Gui_DrawPoint(unsigned short x,unsigned short y,unsigned short Data);
unsigned int Lcd_ReadPoint(unsigned short x,unsigned short y);
void Lcd_SetRegion(unsigned short x_start,unsigned short y_start,unsigned short x_end,unsigned short y_end);
void LCD_WriteData_16Bit(unsigned short Data);
unsigned short LCD_BGR2RGB(unsigned short c);
void Gui_Circle(unsigned short X,unsigned short Y,unsigned short R,unsigned short fc);
void Gui_DrawLine(unsigned short x0, unsigned short y0,unsigned short x1, unsigned short y1,unsigned short Color);
void Gui_box(unsigned short x, unsigned short y, unsigned short w, unsigned short h,unsigned short bc);
void Gui_box2(unsigned short x,unsigned short y,unsigned short w,unsigned short h, unsigned char mode);
void DisplayButtonDown(unsigned short x1,unsigned short y1,unsigned short x2,unsigned short y2);
void DisplayButtonUp(unsigned short x1,unsigned short y1,unsigned short x2,unsigned short y2);
void Gui_DrawFont_GBK16(unsigned short x, unsigned short y, unsigned short fc, unsigned short bc, unsigned char *s);
void Gui_DrawFont_GBK24(unsigned short x, unsigned short y, unsigned short fc, unsigned short bc, unsigned char *s);
void Gui_DrawFont_Num32(unsigned short x, unsigned short y, unsigned short fc, unsigned short bc, unsigned short num) ;
void TFT_SetArea(unsigned short X_Start,unsigned short Y_Start,unsigned short X_End,unsigned short Y_End);
void TFT_ShowImage(unsigned short X,unsigned short Y,unsigned short Length,unsigned short Width,const unsigned char Pic[]);
// TFT 显示字符/汉字/字符串
void TFT_ShowASCII_08x16(unsigned short int X, unsigned short int Y,unsigned char ASCII, enumTFT_Color FontColor, enumTFT_Color BackgroundColor);
void TFT_ShowChinese_16x16(unsigned short int X, unsigned short int Y,unsigned char *Chinese, enumTFT_Color FontColor, enumTFT_Color BackgroundColor);
void TFT_ShowString_16x16(unsigned short int X, unsigned short int Y,unsigned char *String, enumTFT_Color FontColor, enumTFT_Color BackgroundColor);
void TFT_ShowChinese_24x24(unsigned short X, unsigned short Y,unsigned char *Chinese, enumTFT_Color FontColor, enumTFT_Color BackgroundColor);
// TFT 显示有符号整型/无符号整型/浮点型数字
void TFT_ShowNumber_SignedInteger_16x16(unsigned short int X, unsigned short int Y, signed short int IntegerNumber, unsigned char Count, enumTFT_Color FontColor, enumTFT_Color BackgroundColor);
void TFT_ShowNumber_UnsignedInteger_16x16(unsigned short int X, unsigned short int Y, unsigned short int IntegerNumber, unsigned char Count, enumTFT_Color FontColor, enumTFT_Color BackgroundColor);
void TFT_ShowNumber_Float_16x16(unsigned short int X, unsigned short int Y, float FloatNumber, unsigned char Count1, unsigned char Count2, enumTFT_Color FontColor, enumTFT_Color BackgroundColor);
void TFT_ShowNumber_Binary_16x16(unsigned short int X, unsigned short int Y, unsigned short int BinaryNumber, unsigned char Count, enumTFT_Color FontColor, enumTFT_Color BackgroundColor);
#endif
font.h 参考仓库文件
bsp_led.c
#include "main.h"
void LED_init()
{
GPIO_InitTypeDef GPIO_InitStruct;
__RCC_GPIOC_CLK_ENABLE();
GPIO_InitStruct.IT = GPIO_IT_NONE; //控制脚初始化
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pins = LED1_GPIO_PIN;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_Init(LED1_GPIO_PORT, &GPIO_InitStruct);
}
bsp_led.h
#ifndef __BSP_LED_H
#define __BSP_LED_H
#define LED1_GPIO_PORT CW_GPIOC
#define LED1_GPIO_PIN GPIO_PIN_13
void LED_init(void);//初始化
#endif
测试效果
